Grout Bag

A plastic cone-shaped bag used for grouting by hand a deep wall grout injection and for filling in very tight butter joints with a pinhole opening after joints are masked and cut.



Collomix Xo1 Hand Mixer w/Paddle

The Xo1 Collomix Mixer is a Heavy Duty 1010 Watt machine with 1-speed high torque gear unit and variable speed control. Light-weight, compact and economical, but powerful and controllable with double grip two-hand handle it is ideal for mixing loads of up to 10.5 gallons of heavily sanded mixes. Weight-reduced motor housing made of shatter-proof GFRP, a guarded handle and a mixing paddle with quick connect Hexafix® joint.



Colloid CX100HF Paddle

Quick Release Replacement paddle for the Collomix X01 Hand Mixer, for mixing quantities between 4 and 6.5 gallons.



16mm (5/8") Tungsten Point

These chisels are approximately 8" long, are made from High Carbon Tool Steels, and have a cylindrical pointed tip fused into the cutting end. The size stated is the diameter of the Octagonal shank Flat-to-Flat. This tool has a Mushroomed Mallet Head to prevent damage when used with Nylon/Wooden Mallets.



13mm (1/2") Tungsten Point

These chisels are approximately 8" long, are made from High Carbon Tool Steels, and have a cylindrical pointed tip fused into the cutting end. The size stated is the diameter of the Octagonal shank Flat-to-Flat. This tool has a Mushroomed Mallet Head to prevent damage when used with Nylon/Wooden Mallets.



Tungsten Scribe

Used for marking masonry and tooling green Lithomex.



Double Scutch Hammer

Slotted on each end for attachment of two different scutch combs which are used for cutting bricks and stone in the same way as scutch chisels. Comes with a stone scotch comb.



4" Plastic Mell

Used in stonemasonry and wood carving, they are very hard wearing and durable and like wood will absorb some of the shock when striking tools.



Mortar Pick

A traditional bricklayers tool with a chisel and point. The hardened point is used for raking out weathered mortar joints and for digging out clay, shale, sand or chalk, while the chisel end is used for dressing or removing redundant mortar from bricks.



Harling Trowel

Imported "Harling" or "Rough Casting" trowel.



Steel Dummy Mallet

For use with woodcarving and stone carving tools; ideal for use when letter carving.



Churn Brush

Churn brush is a lime mortar compacting tool used when the mix has been installed and has become stiff enough to pack, not swipe across and smear, in order to push lime securely to the back-up material, expose a little aggregate in order to ‘antique’ and blend in all patch-pointing work with the surround original mortar. By the action of beating the stiff mortar straight on the tool also helps to reduce unwanted lime spatter on adjacent units.



6" Lime Brush

Imported from Italy, these are high quality natural bristle brushes that really hang on to thin viscosity paint such as limepaints. Available in either 6" or 4" sizes.



4" Lime Brush

Imported from Italy, these are high quality natural bristle brushes that really hang on to thin viscosity paint such as limepaints. Available in either 6" or 4" sizes.



Perma-Grit Rectangular Sanding Block

Tungsten carbide grit with coarse grit on one side for rapid cutting and shaping and fine grit of the other for finishing. Sands perfect 90 degrees when placed on its side.



Perma-Grit Wedge Sanding Block

Tungsten carbide grit with coarse grit on one side for rapid cutting and shaping and fine grit of the other for finishing. Block is made with a 45 degree angle to reach into tight corners.



Perma-Grit Black Plastic Block Holder With Felt Pad

Sanding block with a felt backing pad and wing nut fastener to hold on Swap Block Sheets.



Perma-Grit Swap Block Sheet

Swap Block Sheet Fine – 320 Grit tungsten carbide sheet for use on Black Plastic Block Holder.
Swap Block Sheet Extra Coarse – Extra Coarse tungsten carbide grit sheet for use on Black Plastic Block Holder.